Leave Your Message
Blank die-cut label rolls with blue glassine liner, wound and standing on a white surface
Loading...
Close view of a blank die-cut label roll with blue liner and visible label gaps
Loading...

Blank Die-Cut Label Rolls — White, Blue & Yellow Glassine Liner

    What these rolls are

    A blank die-cut roll is a web of label stock with the labels already cut and the surplus matrix stripped away, so what leaves the roll is a sequence of separate labels sitting on a continuous liner. The buyer prints them, or applies them blank. Everything that matters about the roll is decided before it ships: the face, the adhesive, the die, the liner and the wind. This page covers the range; each size has its own page because the geometry changes the failure modes.

    The range at a glance

    Item Range
    Face stock Uncoated woodfree, coated paper, direct thermal, white or clear PP, white PET
    Adhesive Permanent acrylic, hot-melt rubber, removable, freezer-grade
    Liner Glassine in white, blue or yellow; PET film on request
    Core 25 mm (1 in), 40 mm (1.5 in), 76 mm (3 in)
    Roll outside diameter Quoted against your applicator's maximum
    Label shape Rectangle, square, circle, oval or custom die
    Gap between labels 2–3 mm typical, set by the die
    Winding Face out or face in, to match the applicator

    Three blank label rolls showing white, yellow and blue glassine liner ends

    Why the liner is coloured

    Coloured glassine is not decoration. The liner is the surface every optical gap sensor looks at, and a sensor works by contrast: it needs to see the difference between the label and the gap. A white label on a white liner is low contrast — the sensor has to be tuned tighter, the line has to run slower, and on a fast applicator that is where missed labels and double feeds come from. A blue or yellow liner puts colour behind the gap, the contrast jumps, and the sensor sees a clean edge. That is the whole function: colour buys sensing reliability. White liner remains the cheaper option, and it is the right one where the applicator senses mechanically or by laser rather than optically.

    Choosing the face

    Uncoated woodfree takes pen and stamp and is the choice for handwriting and manual overprinting. Coated paper gives the sharpest print and is the cheapest per square metre, but it is not waterproof. Direct thermal needs no ribbon at all, and is the most fragile face here — heat, solvent and abrasion all destroy an image that cannot be reprinted. PP film is the default for anything cold, damp or handled; PET adds stiffness and chemical resistance where the label has to survive a wipe-down.

    Choosing the adhesive

    Adhesive is chosen by the surface and the temperature. Permanent acrylic holds on glass, board and most plastics and resists sunlight. Hot-melt rubber grabs harder and faster on rough or recycled board — the usual choice for logistics — but dislikes heat and prolonged UV. Freezer-grade stays tacky below zero, so the label still grips a frosted surface. Removable leaves the surface clean enough to re-label, which suits price changes and promotions and is wrong for a shipping label.

    The eight sizes, and what each is for

    They are not interchangeable: a 40 mm wide label and a 100 mm wide label fail in different ways, need different dies, and suit different applicators. Each size page explains the trade-off for that format rather than repeating the same specification eight times.

    Gap, matrix and the die

    The gap between labels is cut by the die, not by the artwork, and it has a cost: a narrower gap wastes less liner but raises the die cost and the risk of a nick that tears the web. 2–3 mm is usual. The matrix — the surplus material around the labels — is stripped during converting; on very small labels the matrix becomes the weak point, because more of the web is waste and the remaining web is what carries the tension.

    Core, wind and the applicator

    Core size follows the machine: 25 mm for desktop units, 40 mm for mid-range, 76 mm for industrial applicators. Two numbers travel with it — the maximum outside diameter and the wind direction. A roll wound face-in on a machine that expects face-out feeds the liner first, and every label is applied to nothing. It is a one-word instruction that ruins a run when it is wrong.

    What to send for a quotation

    Label size and shape (or the dieline), face stock, adhesive, liner colour, core size, maximum roll diameter, wind direction and the quantity. With the artwork or a dieline we can cut to your shape; with the applicator model we can check the geometry before anything is made.

    Leave Your Message