Leave Your Message
A pale sage card sheet lying on white with gentle waves after inkjet printing and one corner lifted
Loading...
A sand coloured card sheet with one solid blue rectangle whose printed edge is visibly soft
Loading...
A thick teal card display panel standing propped up with a large two-colour geometric print
Loading...

Colour Card for Inkjet and UV Flatbed — Wicking, Cockling and Primers

Inkjet and UV flatbed on colour card: water-based ink wicks along fibre, wetting cockles light sheets, and UV ink sits proud where creases will crack it.

    A sand coloured card sheet with one solid blue rectangle whose printed edge is visibly soft

    Two very different processes wearing one name

    Inkjet and UV flatbed are grouped together because both are non-contact, and they behave almost oppositely on paper. Water-based inkjet wets the sheet, so the sheet reacts: fibres swell, ink travels along them, and the image edges soften. UV flatbed ink cures instantly under a lamp and barely touches the sheet, so the sheet stays flat and the ink stays exactly where it landed — on top of the surface. Choosing between them is a question about the artwork and the finish, not only about the machine.

    Wicking, and why an uncoated sheet has soft edges

    On uncoated card the ink lands on a rough, absorbent surface and travels along the fibres before it dries. The result is a fringe: the printed edge is not a line but a gradient about a fibre long. For a photographic image that is mostly harmless. For small type, thin rules, barcodes or a fine geometric pattern it is fatal, because the detail is smaller than the fringe. The usual answer is an inkjet-receptive coating on the sheet — a thin layer that accepts the ink and holds it at the surface — which converts an absorbent card into a printable one without changing its colour or weight.

    Cockling is the sheet telling you it got wet

    Water-based ink adds moisture to one face of the sheet. That face swells, the other does not, and the sheet waves. Light sheets cockle badly; heavier card resists because there is more thickness to carry the strain, which is one reason inkjet work tends to move up the grammage range rather than down. Practical levers: print the least ink you can get away with, keep the sheet conditioned rather than dry, and let it relax flat under weight before any cutting or folding. A cockled sheet that is cut and folded immediately keeps the waves in the finished piece.

    UV flatbed puts a plastic layer on the paper

    UV ink cures to a solid film with almost no penetration. On a smooth sheet that film is glossy, hard and dimensionally stable, and it stays exactly where it was printed. On a textured or embossed card the ink follows the surface, so the texture reads through the print, which can be an asset or a nuisance depending on the design. On a non-porous or heavily coated sheet the ink needs a primer, or adhesion is poor and the film can be picked off with a fingernail.

    The failure to watch for is at the fold

    A cured UV film does not stretch. On a piece that will be creased, the ink film is the thing that cracks first, and it cracks along the crease as a thin white line in the middle of a printed area. Three ways to manage it: keep printed areas away from the fold, crease and then print, or specify a more flexible ink where the press supports it. Deciding this after the print is running is what turns a small job into a remake.

    Water-based inkjet UV flatbed
    How the ink behaves Wets the sheet, travels along fibre Cures instantly, barely touches the sheet
    Sheet reaction Cockling, soft edges, fibre swell Dimensional stability, sheet stays flat
    Main failure Wicking at fine detail; waves in light stock Ink film cracking along a crease
    Needs from the card An inkjet-receptive coating on uncoated stock A primer on sealed or non-porous surfaces
    Texture Absorbed, so the surface stays matt The texture reads through the cured film

    What to send for a quotation

    Which process — water-based inkjet or UV flatbed — the artwork and the smallest detail in it, whether the sheet needs an inkjet-receptive treatment, the colour reference as a physical sample, the grammage, the sheet size, whether any printed area will be folded or die-cut, and the quantity. If the piece folds through print, say so at enquiry; it changes both the ink and the sheet.

    This is one of eight processes covered in the colour card guide for print and conversion, which sets out what each process asks of the sheet before the colour is chosen.

    Leave Your Message